SkynetAccessibility Scanner · 20 Nov
How-to · 3 min read
How to trigger Home Assistant from a Wear OS watch
You run Home Assistant at home and want to fire a scene from your Wear OS watch with a quick wrist movement instead of tapping through menus. Maybe your hands are full of groceries, or you are on the couch and the phone is in another room. You want the lights to change when you flick your wrist, and you want the watch battery to last the day. And you do not want the living room to go dark every time you wave at someone.
- Published
- 19 Nov 2026
- Delivery
- No. 12
- Topic
- Work and office
- Evidence
- 10 claims quoted from its Google Play page
- Review
- Approved by the founder
01
Why it's hard
The usual route is a dashboard on the watch or a voice command, and both need you to look, tap or talk at the moment your hands are busy. Gesture detection sounds like the fix, but a watch that listens for motion all day burns battery and reads ordinary arm swings as commands. Many people end up wiring something together with a general automation app, a phone relay and a webhook, which breaks the first time one piece updates. Then there is the accidental trigger problem: a gesture that fires on its own is worse than no gesture at all, because you stop trusting it.
This part describes the usual way. It makes no claims about FlickDeck, so nothing is quoted here.
02
How FlickDeck does it
FlickDeck keeps the setup on your Android phone and the action on your wrist. You build a profile on the phone, point an action at a Home Assistant webhook, pick one of three wrist gestures for it and sync it to the watch. The watch only listens for gestures after you arm a short session, and listening stops when you disarm it or the session runs out. That is the part that saves battery and keeps a random wave from switching scenes.
Gesture listening starts only when you arm it and stops when the session is disarmed or expires.Quoted from its Google Play page
Configure an action on your Android phone, sync it to your Wear OS watch, then arm a short session and use a deliberate double twist, flick up, or flick down.Quoted from its Google Play page
Cooldowns, confirmations and haptic feedback cut accidental triggers, and a test mode shows gesture confidence.Quoted from its Google Play page
03
Step by step
- 1Install the phone companion and the watch app, then create a profile on the Android phone (for example one called home).
- 2Add a Home Assistant webhook action that points at the webhook your automation listens for.
- 3Map that action to a double twist, a flick up or a flick down.
- 4Sync the configuration to your Wear OS watch.
- 5Practice in gesture test mode until the confidence feedback shows the watch reads your movement reliably.
- 6When you want to use it, arm gesture mode from the watch app or the Tile, do the gesture, and let the session expire.
04
Tips
If Home Assistant only runs on your home network, you can keep the webhook on plain HTTP, but only for a validated local target. Anything reachable from the internet has to use HTTPS, so expose your instance that way if you want the gesture to work away from home.
Plain HTTP is limited to validated local-network targets, such as a Home Assistant instance on a trusted network.Quoted from its Google Play page
Turn on a confirmation for actions you would not want fired by mistake, like opening the garage or turning off every light. A cooldown also helps, because it stops one shaky movement from sending the same webhook twice.
Confirmation before risky actionsQuoted from its Google Play page
The Tile and the complication are shortcuts to gesture mode and status, not buttons that run your scene. Plan on arming a session first, then doing the gesture, and rely on the haptic buzz to tell you whether the call went through or was rejected.
The Tile and complication do not execute configured actions directly.Quoted from its Google Play page
Start with the free tier and one scene you use every evening. If you later want separate profiles for the desk, bedtime or presentations, that is where the one-time Pro purchase comes in.
Free includes one complete setup with one profile, one action, and one gesture mapping.Quoted from its Google Play page
05
Questions
Do I need an account or a cloud service to use it with Home Assistant?
No. Profiles and actions stay on your devices, and the webhook goes straight to the endpoint you set up.
FlickDeck does not require an account and does not use a developer-operated cloud backend.Quoted from its Google Play page
Can I use it for door locks or alarms?
Not as a safety tool. Gesture recognition is not guaranteed, so the developer says not to rely on it for safety-critical actions.
Gesture recognition is not guaranteed and should not be used for safety-critical actions.Quoted from its Google Play page
Will webhooks with secret headers work from the watch?
Not fully yet. Secret header values are not synced to the watch in the current release, so plan your Home Assistant webhook with that in mind.
Secret header values are not synced to the watch in this release.Quoted from its Google Play page
More on Work and office
FlickDeck has one answer so far, so these come from its topic
ToolsGrid · 19 Nov
How to make a resume applicant tracking systems can read
Approved by the founder
FetchAhead · 19 Nov
A weekly checklist to keep your offline library tidy
Approved by the founder